No obstruction may indicate a water pump failure or blockage in the cooling system. Is WirelessBuy Mobile actually unlimited Hotspot, meaning there is no data caps, no throttling, etc? Screw the hose nozzle into one of the intakes.
Molded cups deliver fresh water from a garden hose to flush the cooling system through side intakes on the lower unit. Reply to this topic Start new topic. Replace spark plug if electrode is worn or the insulator is rough, cracked, broken, blistered, or fouled.
Can I run the motor with that hooked up which would eliminate the need for earmuffs or filling a tub in the driveway? Hook back to tank from boat and does the same thing again. Extends engine life by preventing clogging and corrosion. While the boat is coasting, online dating it can cause injury to anyone in the boat's path as seriously as the boat would when under power. The preferred method is to flush with a flush-muff attachment or built-in port.
These accessories are available from Mercury Marine dealers. Share this post Link to post Share on other sites. Depending on your engine type, insert the key or pull the starter to engage the engine. Align the cable end guide with this center mark when installing cable to the engine.
Motor Flushers for Outboards and Sterndrives
Store your fuel line out of the sun. If you do not find what you are looking for please fill out the info form and we will find the parts you need and respond with a quote. It never had a tranny issue. Move the steering friction lever back and forth while lubricating.
Slide the fuel hose onto the barbed fitting and secure it using a hose clamp and Phillips screwdriver. Your manual will most likely recommend covering the other intake with heavy tape. Save all maintenance work orders and receipts. Connect to a garden hose, fit the muffs over the engine's water intakes on the sides of the gear case, turn the water on, start the engine, and let it run. Positioning Outboard for Storage Store outboard in an upright vertical position to allow water to drain out of outboard.
It's an integrated power system. Using the flushing port on the back of the engine, you can flush the engine with or without running it. Turn your boat left and right and note the direction the boat turns more easily. Refer to your Operation and Maintenance Manual for full details of your warranty coverage. As a matter of fact, most of the cooling water exits through the prop.
Here's to convenience and having more uninterrupted hours on the water. Which ever method you choose, recovering alcoholic after flushing leave the engne in the tilted down position and make sure the water is drained from the engine before tilting up. Flush bags allow for engine-on flushing without the loud noise of the engine's open exhaust.
- This enables the operator to easily adjust the position of the outboard by pressing the trim switch.
- This article was co-authored by our trained team of editors and researchers who validated it for accuracy and comprehensiveness.
- Be sure the engine is receiving cooling water by checking the overboard indicator.
- Mercury Marine will work with you and your dealership to resolve all problems.
Thank you thank you for this post! Water pressure should be set to one-half or more to ensure adequate flow to the intakes. Unscrew the hose from the muffs or built-in attachment.
Pump the primer bulb in the fuel hose until the inline filter is filled with fuel and the bulb has a firm feel when it is squeezed. Does anyone know if you can leave a standard garden hose quick connector in the flushing port all the time? This would be hooked up to my router and used as whole home internet.
Page Operation Wash the outboard exterior and flush out the exhaust outlet of the propeller and gearcase with fresh water after each use. Noticed the primer ball is deflating. Replaced the water separator and primer ball and it ran fine for a day then back to cutting off and the ball deflating. The enclosed Owner's Registration Card is your key to trouble-free family fun. View Bulletins for all Models.
Provide a sufficient supply of water to the water inlets during operation. Louis Maconi mine was probably too old to have this issue, but who knows. Folded the liner over and plugged the gas line.
Outboard Fuel Line
After you run it for a while it should begin to come out. Here is a link on how to modify the Evinrude quick-disconnect flusher to work with your motor, and you can leave the adapter attached to your outboard. Place a block of wood between the propeller blade and the anti-ventilation plate.
Gasoline-powered outboard motors without built-in fuel tanks must be connected to a remote fuel source. The serial number is located on the outboard as shown. Moving the outboard in closer to the boat transom is called trimming in or down. You should see a stream of water flowing out of the top of the motor. Have you changed all the fuel hose from the tank to the motor.
Quickly flushes away salt, silt, alkali and sand. When using the flushing port, wilmington nc speed dating it is not necessary to run the engine. But dies off at full throttle.
These catalog pages represent just a few of the parts we stock. Cleaning Exterior Systems. High density polyethylene five-ga.
This 5.6L V8 is more than an outboard. It s an integrated power system
Mercury's procedure varies by engine size and series. Seems like you should but I guess I'd like some assurance before I do. Additional clearance may be required for railroad crossings, driveways and trailer bouncing. Simple spray on application. Ensure that the filter is in a protected but accessible area of the boat.
- Your motor will have to warm up before the thermostat opens up to allow water to cool your engine.
- All the more reason for a spare.
- Started following you after Totem mentioned you and I love what you do.
- The trim tab can help to compensate for this steering torque in many cases and can be adjusted within limits to reduce any unequal steering effort.
- Use of other than Mercury Precision or Quicksilver parts when making warranty repairs.
- Injury or damage will result if the engine accidentally slips into gear and the connecting rod is on the propeller side of the motor.
Just a shot to the left of the High Water Mark. Hoping that does the trick. Carbon-coated Lifters A special carbon coating on shimless, dating ultrasound bucket-style valve lifters increases durability and requires less maintenance.
Now the lead is almost gone and injuries are piling up. Back in the day, flushing an outboard with fresh water was done only one way. This will protect the connector stem from being accidently pushed-in, thus, allowing fuel or vapor to escape. If not, talk to your mechanic or dealer.